📞 +33 (0)1 60 24 40 45 ✉️ contact@involtec.com Le Châtelet-en-Brie (77) — France
FREN

PPWR: what the European packaging regulation changes for your lines

Practical guide no. 14 · Published on 25 August 2026 · Frédéric Bussemey
INVOLTEC practical guide no. 14 — PPWR: what the European packaging regulation changes for your lines

Regulation (EU) 2025/40 has applied since 12 August 2026. The question is no longer whether to change your packaging, but what your machine will be able to do with the new packaging.

A change in nature, not just in the level of requirements

For the past ten years, pressure on packaging had come from brands, retailers and consumers. It was strong but negotiable.

It now comes from a directly applicable EU regulation.

Regulation (EU) 2025/40 on packaging and packaging waste, known as the PPWR (Packaging and Packaging Waste Regulation), entered into force on 11 February 2025 and has applied since 12 August 2026. It repeals Directive 94/62/EC.

What makes it distinctive is its legal form: it is a regulation, not a directive. It therefore applies in the same way in every Member State, with no national transposition and no room for local interpretation.

For a manufacturer running packaging lines, this changes one essential thing: the deadline is no longer an intention, it is a date.

Free access · all INVOLTEC practical guides

Read the rest of the guide

Enter your business contact details: you get immediate access to the whole of this guide and all INVOLTEC guides, on this device.

Coming up in the rest of the guide:

  • What already applies, and what is coming
  • The point that directly concerns secondary packaging
  • What this changes in practice on an existing line
  • What to check on your machine before committing to a change
  • The timetable to meet, working backwards
  • The most common mistakes
  • … and 2 more sections

INVOLTEC uses your data to give you access to the guides and to contact you again about solutions relevant to your business; you may object to this at any time. Your data is neither transferred nor sold. Privacy policy.

What already applies, and what is coming

The regulation does not switch over all at once. Its obligations are phased in over some fifteen years, and that is precisely what makes it hard to read.

Timeline: 12 August 2026, 1 January 2030, up to 2040
Diagram — The PPWR timetable.

Three time horizons need to be distinguished.

Since 12 August 2026.

  • The regulation applies and replaces Directive 94/62/EC.
  • Limit values apply to per- and polyfluoroalkyl substances (PFAS) in food-contact packaging.
  • All packaging placed on the market must be accompanied by a declaration of conformity that identifies it and attests to its compliance.

From 1 January 2030 — the defining deadline.

  • All packaging must be recyclable according to defined design criteria; non-recyclable packaging may no longer be placed on the market.
  • Packaging must be designed so that its weight and volume are reduced to the minimum necessary for its functionality, which the producer must be able to demonstrate in a technical file.
  • Plastic parts must contain a minimum percentage of recycled content.
  • Grouped and transport packaging are subject to a maximum empty space ratio.
  • A list of single-use plastic packaging formats is banned from being placed on the market (Annex V to the regulation).

Beyond 2030.

  • Recycled-content percentages and reuse targets are raised in stages up to 2040.
  • Member States must reduce packaging waste per capita compared with 2018, according to successive milestones.

A manufacturer investing in a line today will still be running it in 2035. That is why this timetable belongs in the specification, not in the CSR report.

The point that directly concerns secondary packaging

Two provisions deserve particular attention because they concern over-packaging, in other words the very core of the trade.

Minimisation.

From 2030, packaging must be reduced to the minimum necessary for its functionality. The wording matters: the text does not say “eliminated”, it says “reduced to the minimum necessary for its functionality”.

In other words, the question is not whether secondary packaging is permitted. It is whether its function can be demonstrated.

Overwrapping fulfils identifiable functions: tamper evidence, protection against dirt and handling, holding a multipack together, hygiene. These functions can be documented — but they need to have been documented before anyone asks.

Banned formats.

From 1 January 2030, Annex V to the regulation bans a list of single-use plastic packaging formats deemed non-essential. They include, in particular, non-functional overpackaging and certain plastic grouped packaging used at the point of sale.

The exact scope of this category is currently interpreted in different ways within the industry. Two reference points, however, are solid: the ban applies only to plastic, and it applies to what is non-functional.

These two reference points outline the strategy to follow: document the function, and examine non-plastic alternatives.

What this changes in practice on an existing line

A change of material is never a simple reel swap. It affects five parameters at once.

  • The sealing window. Each material has its own combination of temperature, dwell time and pressure. Heat-sealable papers and cellulose films are noticeably less forgiving than polypropylene.
  • Output. A less flexible material, or one with a narrower sealing window, may require output to be reduced, sometimes significantly.
  • Tooling. A change in web width or stiffness may require change parts to be adjusted or even replaced.
  • Tension and guiding settings, which must be revalidated format by format.
  • Storage. Bio-based and paper materials are sensitive to humidity, temperature and static electricity; unsuitable storage degrades their machine behaviour long before their appearance.

That is why the right sequence is always the same: production trial first, marketing decision second. The reverse produces lines that can no longer hold their output.

Practical guide no. 6 describes the available families of materials and their conditions of use in detail.

What to check on your machine before committing to a change

Not all machines are equally open to alternative materials. Four points determine the room for manoeuvre:

  • the temperature range of the sealing units and the precision of their control;
  • the ability to store and recall separate recipes for each material, failing which every changeover becomes a full set-up again;
  • control of material tension along its entire path, which becomes critical with less forgiving materials;
  • the availability of manufacturer support for revalidating parameters.

On an older machine, these four points also provide a decision grid between upgrading and replacement — a topic covered in practical guide no. 16.

The timetable to meet, working backwards

You do not prepare for a 1 January 2030 deadline in 2029.

Changing the material across a complete range involves, in order: an inventory of SKUs and their packaging functions, a shortlist of materials, production trials for each format family, revalidation of parameters, possible adaptation of tooling, a redesign of print artwork, then running down existing reel stocks.

Counting backwards, this puts the start of trials well ahead of the deadline. Manufacturers who start late generally discover two things at once: that the chosen material cannot sustain the required output, and that there is no time left to test another.

The most common mistakes

Treating the PPWR as a CSR topic. It is a product compliance issue, with an application date and a burden of proof. It belongs in the industrial specification as much as in the non-financial report.

Waiting for the text to be finalised. Some details have yet to be clarified, but the deadlines are fixed. Material trials can start straight away.

Changing material without a trial on the actual line. Two similar commercial grades can behave very differently in sealing and at speed. A laboratory test is no substitute for a production trial.

Removing secondary packaging without documenting its function. The text requires reduction to the minimum necessary for functionality, not elimination. An undocumented function is an indefensible function.

Forgetting the impact on tooling and printing. Web width, stiffness and heat-sealable areas must be decided together. Reworking them separately costs twice as much.

Checklist: where do you stand on the PPWR?

  • ☐ Has the function of each pack in your range been identified and documented?
  • ☐ Has your single-use plastic packaging been reviewed against Annex V?
  • ☐ Is there an inventory of the SKUs and web widths used?
  • ☐ Have alternative materials been shortlisted for each format family?
  • ☐ Have production trials been carried out on your line, with your product?
  • ☐ Has the impact of these materials on output been measured, rather than estimated?
  • ☐ Do your sealing units cover the required temperature range?
  • ☐ Do your production recipes allow you to switch from one material to another without complete readjustment?
  • ☐ Have your print artwork and heat-sealable areas been reviewed with your printer?
  • ☐ Has a timetable working back from the 2030 deadline been drawn up, including running down stocks?

Conclusion

The PPWR does not condemn secondary packaging. It condemns secondary packaging whose purpose no one can explain.

Two workstreams need to be run in parallel: documenting the function of your packaging, and checking what your machines can do with the materials that will replace the current ones.

The second workstream takes longest, because it involves production trials rather than desk-based decisions. That is therefore where you need to start.

Sources

Regulation (EU) 2025/40 of the European Parliament and of the Council of 19 December 2024 on packaging and packaging waste, repealing Directive 94/62/EC.

Entry into force: 11 February 2025. Application: 12 August 2026. Subsequent milestones: 2028, 2030, 2035, 2040.

INVOLTEC practical guides

Get every new guide

A guide every three to four weeks, written by our technicians: machine selection, settings, tooling, regulations.

See all guides →
Article written by Frédéric Bussemey for INVOLTEC International. ← All practical guides