Packaging glossary
The main terms in overwrapping, pouch packing and secondary packaging, explained simply by INVOLTEC. This glossary includes definitions already used in our FAQ.
Packaging technique in which a box, usually made of board, is wrapped with film or paper using an X-fold, to protect and present the product at the point of sale. It is one of the secondary packaging techniques, alongside case packing, cartoning and palletising: overwrapping is a technique, and secondary packaging is the category that includes it. Widely used in premium markets (perfumery, cosmetics, gift boxes), it provides a neat finish, gloss or matt depending on the film, and protects against dust and handling before purchase. Recent films and papers generally have proven environmental properties (recyclable or bio-based depending on the grade).
Machine that performs overwrapping: it automatically wraps boxes or cartons with film or paper using an X-fold.
Packaging in direct contact with the product (box, carton, bottle, sachet…).
Packaging that is not in direct contact with the product, applied after primary packaging (box, carton, bottle). It covers all the operations that protect, present or group this primary packaging before shipping or shelving: overwrapping, case packing, cartoning, film wrapping and palletising are all part of it. The choice between overwrapping, case packing or a combination of both depends on the product, the distribution channel and the desired on-shelf image.
Case formed around the product from a flat cardboard blank: the blank is taken from a magazine, formed around the already-grouped product, then closed by gluing the flaps. Unlike a pre-formed regular slotted case, a wrap-around case fits the pack exactly, eliminating empty space inside and reducing the material used.
Two-part packaging: a shallow tray that holds the products, and a lid that fits over it. Also called base-and-lid, or tray & lid. The lid protects the pack during transport and can be removed in store to display the tray on the shelf.
Tray designed to be placed on the shelf as is: its front face is cut lower so that the products remain visible and accessible without unpacking. It serves both as transport packaging and as a point-of-sale display.
Packaging machine that works in three stages: forming the film from a reel, feeding the product horizontally into the sachet or film pouch, then continuously sealing the pack around the product.
Packaging technique for wrapping products of various shapes in a plastic film passed through a heat tunnel so that the film shrinks around the product. Unlike overwrapping, there are few eco-friendly shrink-wrapping solutions.
Part that keeps the machine running properly, regardless of the dimensions of the packed product (belt, cylinder, circuit board, sensor…).
Part specific to a given product format that allows the product to pass through the packaging machine (guides, templates, positioning parts).
Assigning a unique identifier to every packed product to ensure traceability throughout the supply chain. It helps combat counterfeiting, secure product recalls and meet regulatory requirements.
All the devices and systems used to track and trace a product throughout its supply chain, often combined with serialisation.
Acceptance test carried out in the factory or at the supplier’s premises to validate that a machine (particularly a used one) works properly before delivery to the customer.
French quality certification awarded to training providers, mandatory for them to access public or pooled funding (notably OPCO).
Platform for assessing the CSR (corporate social responsibility) performance of companies and their suppliers, covering environment, labour & human rights, ethics and sustainable procurement.
Clear or coloured plastic film, mono- or bi-oriented (BOPP), gloss or matt, commonly used for overwrapping.
Alternative to plastic film for overwrapping, offering a different finish and properties depending on the machine and the product.
Equipment that measures and dispenses a precise quantity of product (powder, granules, liquid…) before or during packaging.
Secondary packaging operation in which parcels or cases are grouped on a pallet, usually at the end of the line.
Operating and setting up an overwrapping machine
The terms used by our trainers during our Qualiopi-certified training courses, from the film reel to machine maintenance.
The width of the film, measured from one edge of the web to the other. Too narrow and it does not cover the product; too wide and it creates excess film and creases. Together with the cut-off length, it defines the film cut.
The length of film needed to wrap a product completely. It is calculated from the product dimensions and the type of fold.
The reel is the roll of film mounted on the machine; the core is the central tube on which the film is wound and by which the reel is held on its shaft.
The force with which the film is held taut between the reel and the wrapping area. Incorrect tension shows immediately: creases, film that floats or breaks.
Joining two layers of film by heat. Seal strength depends on three factors: temperature, dwell time and pressure. It is made by sealing bars or sealing pads.
The seal that closes the film along the full length of the pack. Depending on the machine, it is placed under the pack or on its rear face, leaving the front face intact.
The ways of folding the film at the ends of the product before sealing. The choice of fold changes the film width and the setting of the folding parts: it is a setting parameter, not an aesthetic detail.
The folding carton that holds the product and is wrapped. Its shape and rigidity directly affect overwrapping quality: a flimsy or poorly closed carton does not overwrap well.
The complete set of change parts for a given product. Having several sets means one format can be prepared while the other is in production.
The part that raises the film around the product before longitudinal sealing.
The parts that fold the film down and guide the product as it advances through the machine.
The knife, with its fixed and moving blades, that cuts the film to the cut-off length.
The combination of a product, its tooling and the associated machine parameters. “Switching to format X” means installing this combination.
Switching from one known format to another: existing tooling is refitted and previously saved parameters are recalled.
Developing a format that does not yet exist: new parameters have to be determined, entered, tried, validated and then saved. It takes longer and is trickier than a format changeover.
A cycle is the complete sequence of operations needed to wrap one product; output is the number of cycles completed per minute.
The control screen, also called the panel, used to view and change the machine parameters, often with several access levels depending on the user’s role.
The set of parameters stored for a given format, recalled in a single action during a format changeover.
A mechanical cam is a rotating part whose profile controls the movement of a component. A virtual cam triggers or enables a movement at a precise position in the cycle, set from the screen and synchronised with the mechanical cams.
A badly formed fold that is crooked, open or creased. Possible causes: film tension, folder position, carton rigidity.
An open, burnt or incomplete seal, caused by temperature, dwell time or pressure.
The troubleshooting method of changing a single parameter, observing the effect, validating or reverting, then moving on to the next.
Making the machine safe before any intervention: stopping it, cutting off and isolating electrical and pneumatic energy, dissipating residual energy, then checking that no energy remains, under a personal padlock.
Regularly checking and recording the machine’s key measurements (positions, clearances, temperatures), always at the same measuring points, to detect drift before it causes defects.
Preventive maintenance is carried out before a breakdown, at regular intervals: cleaning, inspection, lubrication, replacement of wear parts. Corrective maintenance takes place after a breakdown or an observed defect.
A part that deteriorates with use and is replaced periodically: belts, blades, seals, sealing wires or heating elements.
